H&k Squeeze Cocker - The Heckler & Koch P7 is a German 9×19 mm semi-automatic pistol designed by Helmut Weld and manufactured by Heckler & Koch GmbH (H&K) from 1979 to 2008. It was first released to the public in 1976 as the PSP (Polizei-Selbstlade-Pistole - "Self-Loading Police Pistol").
The P7M13, a twin-stack magazine variant of the P7, was in production until 2000 and replaced the M1911 pistol with the US Army's failed XM9 pistol test.
H&k Squeeze Cocker
The 1972 Munich Olympics coup led German police forces to decide to replace the .32 ACP Walther PP with the similarly sized but more effective Parabellum 9×19mm pistol.
H&k P7 M13 9mm Blue 4.1\
The new weapon had to meet the following requirements: Parabellum cartridge chamber 9 × 19 mm, weight not more than 1000 grams (35 oz), gun dimensions not more than 180 × 130 × 34 mm, it should have a muzzle. An energy of less than 500 J and a service life of at least 10,000 rounds The gun must also be fully double-barreled, capable of securing a loaded chamber (both holstered and concealed in the pocket) and quick draw, and ready to fire immediately.
As a result of a competitive bid, the German police force selected three pistols for service: the Swiss SIG Sauer P225 (designated P6) and two of German design – the P7 (officially PSP) and the Walther P5.
Serial production of the P7 began in 1979 The gun was later received by the German Federal Police's anti-terrorist unit (GSG 9) and the German Army's special forces.
The P7 was primarily manufactured by H&K, but was also manufactured in Mexico under license by the Departmenta de Industria Militar (DIM) as a box weapon for officers and staff.
H&k P7m8 Squeeze Cocker 9 Mm Pistol With Four M... For Sale
The P7 is a Blackbuck powered semi-automatic firearm A unique gas delay system, the Swiss Pistole 47 W+F (Waffabrik Burn) prototype pistol model.
Which used the gas pressure of the fired cartridges to feed them through a small port in the barrel (in front of the chamber) to slow the slide back. This is accomplished by means of a piston in a cylinder located under the barrel, which resists the rearward movement of the slide until the gas pressure decreases—after the bullet leaves the barrel—allowing the slide to retract, opening the flap. and removing the empty cartridge case
Which aids in the exhaust process by allowing combustion gases to flow between the combustion case and the chamber walls, which adhere to the chamber walls. The problem with this system is that the rod "rests" a little too quickly to allow the slider to begin its backward motion. The high temperature gas located below the chamber area and above the trigger made early versions of this gun uncomfortable to fire, according to some, after two magazines were fired due to the heat. The advantages of this system are the simple manufacturing process due to the high mechanical precision due to the abs of the locking system and the fixing of the tube to the frame. The barrel undergoes no lateral or vertical movement during the duty cycle, as in browning chamber systems common to other bolt-action pistols.
The fixed ejector is the engagement surface of the slide while the P7 has a spring ejector within the slide.
Heckler & Koch P7 M13 Squeez
The grip of this pistol features a built-in cocking lever located on the front of the grip. Before firing the gun, this lever must be depressed; So this lever acts as a safeguard The gun was fired by an assailant.
Squeezing the cocking lever with a force of 70 N (15.7 lbf) pulls the firing pin. Once fully depressed, only 2 lbf (8.9 N) of force is required to cock the weapon The weapon fires with a one-stage trigger pull rated at approximately 20 N (4.5 lb).
) as long as the trigger is depressed, the weapon fires like any other semi-automatic pistol. If the handle is released, the weapon is immediately disengaged and stored safely While the chambered wheel provided safety to the user carrying the pistol, this mechanism eliminated the need for a manual safety selector and increased firing speed by activating the pistol. The action of the trigger and firing mechanism (and the unique slide catch) were protected by US Patt 4,132,023 issued on January 2, 1979.
Which is held in the frame of the weapon which is located at the heel of the grip After the last round is fired, the slide will remain engaged thanks to the slide catch which can be released by pulling back the slide or depressing the pitch cocker.
My Hk P7 In The Snow
The weapon uses a fixed, multi-point rifling barrel (hexagonal with a 250mm twist rate) and a fixed, wrought iron swingarm with a counterpoint capable of firing in low-light conditions. The gun is fully two-stage and two-handed use is possible through the use of a profile and large trigger guard
Between 1982 and 1983, the P7 received several modifications, mainly to meet the demands of the American market and the preferences of shooters. These changes resulted in the P7M8 model A new magazine release lever (available on both sides of the frame) was installed behind the trigger guard, which forced the designers to change the gun's frame and magazine.
The trigger guard was replaced with a synthetic heat shield to protect the shooter from overheating, and a loop attachment loop was added in place of the former magazine heel release. The firing pin and its bushing have also been replaced
Heckler & Koch P7K3 (.22LR slide and barrel installed, additional .32ACP (7.65 mm) slide, barrel and two magazines visible with change tool and carbon scraper)
Hk P7 & Steyr M
.32ACP barrel installation using the Heckler & Koch P7K3 barrel tension change tool.
Several other variants were built based on the P7: P7PT8, P7M13, P7K3, P7M10 and P7M7, none of which remained in production. Production of the "P7" heel release design began in 1997 with a KH code gun marked "P7" and "PSP" on the slide.
The P7PT8 is a dedicated, simple practice pistol modified for use with the 9×19mm PT practice cartridge (manufactured by Zeco) with plastic bullets (weight 0.42g).
A "floating chamber" adapter is used inside the barrel to provide recoil for use with special ammunition. The guns were marked with blue dots on either side of the slide to distinguish the P7PT8 from other P7 guns that could be fired.
Hk P7 M13
To date, about 200 guns of this type have been produced, which are mainly used for simulated shooting in confined spaces.
The P7M8 is the counterpart of the P7 with a larger trigger guard, longer trigger guard, heat shield, finger operated magazine release, larger rear sight tail, firing pin bushing and rope ring. Production began in 1983 and continued until 2007 The final production run date of 500 P7M8 pistols was produced under code AH (2007). Each is marked with an X of 500 on the right side of the slide Other than slide marking, no other features or accessories are added to the normal kit. To commemorate 25 years of production of the P7, H&K has released a limited run of the P7M8 "anniversary" edition. Only 500 examples are given The package includes a wooden lock case, a P7 challenge coin and special tag The Radius tip on the top left of the slide bears its designer's name (Helmot Weldl) and "1 von 500" (German, double quote included; translates to "1 of 500" in Luster) The wood grips were made by Karl Nils and bear the H&K logo. |
This gun was the US Army's XM9 pistol test, replacing the old M1911 pistol.
A variant known as the P7M13SD was produced in limited numbers only for German special forces, with a longer threaded barrel (compared to the P7M13) and a sound suppressor.
Sold Price: H&k P7 M8 9mm Lnib
The P7K3 is a shortened version of the P7 (inspired by the HK4 pistol) that uses a direct trigger for action. This version has a removable barrel and uses a sealed hydraulic recoil buffer instead of a gas cylinder.
After replacing the barrel and magazine, it can use a .380 ACP (9×17mm Short) or .32 ACP (7.65×17mm Browning SR) pistol, and after replacing the slide, magazine and barrel (with floating chamber) – it can. Also used to fire .22 LR (5.6mm Long Rifle) ammunition.
The P7K3's hydraulic recoil buffer is subject to wear and poses a serious problem in controlling the gun when worn. Heckler & Koch does not make a replacement part for the buffer However, there are some commercial buffers available When the slide and .22 LR barrel are installed, the buffer does not jam The .22 LR has a slot in the front of the slide that avoids using the buffer when firing the gun. Heckler & Koch offers a special scoring tool for .22 LR barrels Tools required
K&h, k and h windows, h k, h& k, hk squeeze cocker for sale, h & k, h &k, k & h windows, h&k, h&k squeeze cocker p7, squeeze cocker, h k
0 Comments